恒旺厂家供应 螺旋钻机 轮式履带式 速度快口径大 桩工机械

螺旋钻机采用加压钻进工作模式，可实现旋挖桩深2.5米、5.5米、11.5米，选配不同规格的钻具，桩孔直接范围可达直径200-1200mm，施工完毕将钻杆收复归位后，可以每小时0-30公里的速度快速转场，机动灵活，便捷高效，是国家高铁建设专用的桩工机械设备。

Spiral drill the pressurized drilling work mode, can realize the rotary digging pile deep 2.5 meters, 5.5 meters, 2.5 meters, equipped with different specifications of the drill, the pile hole directly range can reach 200-1200 - mm diameter, finished, recovered after place, will drill pipe can be 0 to 30 km per hour speed quick turnarounds, flexible, convenient and efficient, is the country dedicated high-speed rail construction pile driving machinery equipment.

适用于土层、黏土层、填土层、粘土层、粉土层、淤泥层、沙土层及部分含有卵石的地层，适用于高铁接触网支架桩、护坡桩，太阳能光伏电站地基支架桩，电网改造、民用建筑、新农村建设、市政工程建设、园林绿化等多种工程项目。

Applied to the soil, clay layer, fill soil, clay, powder soil and silt layer, sand layer and part includes the pebble stratum, is suitable for the high-speed catenary stent pile, slope protection, solar photovoltaic power station pile foundation support, network reconstruction, civil construction, construction of new countryside construction, municipal engineering, landscaping and other projects.

机动灵活：整机吨位小，操作简单，移动快速，转场便利，具有一个桩孔也能打的特点。

Flexible: the machine tonnage small, simple operation, move fast, convenient transitions, have the characteristics of a pile hole can also be played.

螺旋钻机安全操作规程

1、司机必须经培训合格后，方可上机操作，所有工作人员应穿绝缘鞋，戴安全帽。

2、应配正副司机各一人，司机酒后或患病不得上机操作。

3、司机必须进行设备的日常维护保养，对机械状况认真填写记录。

4、工作前应检查电机及其它电器绝缘情况，发现问题随即处理。

5、桩机施工现场应在离开高压电线(缆)、油气管道的有关规定危险距离以外工作。

6、起落立柱应有专人指挥与操作，支脚与履靴应同时接地，前支腿伸于前方，立柱、斜撑下严禁站人。

7、桩机移位时应有专人指挥，并安排人员移动电源线以防碰压。支脚下松软时应用枕木等辅垫以保证接地比压。

8、桩机移动、回转时严禁用上盘、履靴顶土或排除障碍物。特别提示：钻机、回转时移动前应及时清土、清障处理；支腿支起否则极易发生钻机损坏事故，影响正常施工。

9、施工现场不平度应小于2°，地面承载力不小于100kPa。

10、钻孔时注意调整立柱垂直度，并应使支脚与履靴同时接地。

11、本机在六级以下风力工作。在大风雨雪天气应停止施工，且在大风时应加缆绳予以保护。

12、施工中若桩机回转支路频繁自动停止，其一应检查电机综合保护器电流刻度调节值是否合适，其二应及时排除桩机回转过程中的障碍。

Spiral drill safety operation procedures
1, the driver must be qualified after the training, can use the computer operation, all the staff should wear insulated shoes, wearing a helmet.
2, the driver should be under each one, "the driver drunk or sick computer operation is not allowed.
3, the driver must conduct equipment daily maintenance, fill in record for mechanical condition.
4, before work should check the motor and other electric insulation, found the problem immediately.
5, pile machine construction site shall be left high-voltage wire (cable), the relevant provisions of the oil and gas pipeline risk distance work.
6, ups and downs column should be the specialist command and operation, the leg and the shoe boots should ground at the same time, the front leg stretched out in front, columns, it is forbidden to stand under brace.
7, pile machine shift personnel command, and arrange personnel to move the power cord to prevent bruising.When the feet soft sleeper applications auxiliary pad to ensure the ground pressure.
8, pile machine movement, it is forbidden to use when turning plate, the shoe boots top soil or eliminate obstacles.Special note: when the drill, rotary movement should be timely clean soil, repair processing before,Drill leg up otherwise easily happened damage accidents, affect the normal construction.
9, the roughness should be less than 2 ° to the construction site and the ground bearing capacity not less than 100 kpa.
10, drilling, pay attention to adjusting column vertical degree, and should make the leg and the shoe boots ground at the same time.
11, the machine work under 6 wind.In wind rain and snow weather should stop construction, and should add the cable protected when strong winds.

12, If, during the construction of the pile machine rotary branch automatically stop frequently, one should check the motor synthetical protector current scale adjustment value is appropriate, the other should be promptly eliminate the obstacles in the process of turning machine.

高额回报：投资小，收益快，经济优势不可代替。

High returns: small investment, fast gains for economic advantage.

济宁恒旺工矿机械专注机械十年，全国联保，值得您的信赖